D-SOLVE GRAFFITI REMOVER 1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
Staden Lane Business Park, , Buxton, Derbyshire. SK17 9RZUnited Kingdom
Tel : 01298 26226Fax : 01298 26540Email : sales@selden.co.uk
2 HAZARDS IDENTIFICATION 3 COMPOSITION/INFORMATION ON INGREDIENTS
The Full Text for all R-Phrases are Displayed in Section 16
4 FIRST-AID MEASURES
Move the exposed person to fresh air at once., If breathing stops, provide artificial respiration., Keep the affected person
warm and at rest. Get prompt medical attention., For breathing difficulties oxygen may be necessary.
DO NOT INDUCE VOMITING!, Remove victim immediately from source of exposure., Rinse mouth thoroughly., Provide rest,
warmth and fresh air., Get medical attention immediately!
Remove affected person from source of contamination., Remove contaminated clothing., Get medical attention if irritation
Promptly wash eyes with plenty of water while lifting the eye lids., Continue to rinse for at least 15 minutes., Contact
5 FIRE-FIGHTING MEASURES
Fire can be extinguished using:, Foam., Dry chemicals, sand, dolomite etc.
Avoid breathing fire vapours., Cool containers exposed to flames with water until well after the fire is out., Emits combustible
gases if heated., Be aware of danger for fire to re-start. 6 ACCIDENTAL RELEASE MEASURES
Extinguish all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate., Clean-up personnel should use respiratory
and/or liquid contact protection., Absorb in vermiculite, dry sand or earth and place into containers.
Any spillage needs to be contained and not allowed to enter water courses
7 HANDLING AND STORAGE
Avoid spilling, skin and eye contact., Keep away from heat, sparks and open flame., Ventilate well, avoid breathing vapours.
Use approved respirator if air contamination is above accepted level., Use explosion proof electric equipment.
Flammable/combustible - Keep away from oxidisers, heat and flames., Store in tightly closed original container in a dry, cool
and well-ventilated place., Keep in original container. 8 EXPOSURE CONTROLS/PERSONAL PROTECTION TWA - 8 hrs STEL - 15 min
Provide adequate general and local exhaust ventilation.
Respiratory protection must be used if air contamination exceeds acceptable level.
Use protective gloves made of:, Rubber (natural, latex).
Use approved safety goggles or face shield.
Wear appropriate clothing to prevent any possibility of liquid contact and repeated or prolonged vapour contact. 9 PHYSICAL AND CHEMICAL PROPERTIES
MATERIAL SAFETY DATASHEET - T070 : D-SOLVE GRAFFITI REMOVER Page 1 of 2
10 STABILITY AND REACTIVITY
Stable under normal temperature conditions.
Avoid heat., Avoid contact with oxidisers or reducing agents.
Fire creates:, Toxic gases/vapours/fumes of:, Carbon monoxide (CO)., Carbon dioxide (CO2). 11 TOXICOLOGICAL INFORMATION
Vapours may cause headache, fatigue, dizziness and nausea.
Liquid irritates mucous membranes and may cause abdominal pain if swallowed.
Prolonged or repeated exposure may cause severe irritation.
Spray and vapour in the eyes may cause irritation and smarting. 12 ECOLOGICAL INFORMATION
Not classed as Hazardous to the Environment but release to the environment should be avoided. 13 DISPOSAL CONSIDERATIONS
Dispose of waste and residues in accordance with local authority requirements. 14 TRANSPORT INFORMATION 15 REGULATORY INFORMATION
S2 Keep out of the reach of children, S23 Do not breathe vapour/spray., S37/39 Wear suitable gloves and eye/face
protection., S51 Use only in well-ventilated areas.
Chemicals (Hazard Information and Packaging) Regulations., Control of Substances Hazardous to Health.
Classification and Labelling of Substances and Preparations Dangerous for Supply.
Workplace Exposure Limits EH40., Introduction to Local Exhaust Ventilation HS(G)37., CHIP for everyone HSG(108). 16 OTHER INFORMATION
The following risk phrases relate to the raw materials in the product and not the product itself:-
R11 Highly flammable., R36 Irritating to eyes., R67 Vapours may cause drowsiness and dizziness.|
MATERIAL SAFETY DATASHEET - T070 : D-SOLVE GRAFFITI REMOVER Page 2 of 2
H. LAVAL HARLEY Principal Scientist with extensive experience in solving Pharmaceutical processing and Medical Device concerns related to manufacturing process and development. Wide background in pharmaceutical operations: with a proven track record in process / technical development, manufacturing, validation, research and development, manufacturing process site to site transfer. Manufacturin